TrackIQ Installation Disc Help - Configuration

RailBAM Technical Note		Document No.:	51R-05-5656-TNT-422451-0
Author:	Bernard Buterin	Reviewed by:

To Start, Launch Configure.EXE or SETUP.EXE

---

This is the Product Selection Menu (First Run)

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

    
 Select System Type;

  0- RailBAM System
  1- WCM System

  2- RailSQAD System
  3- Camera System
  4- LoV System
  5- Rail Noise Monitor System
  Q- Quit

Select the System Type you wish to configure.
Quit - Exit without changes
The Installation Disc is Dynamic, if an option is not shown to you, it may not have been included in your copy.

---

This is the Product Type Configuration Menu

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

 [Type] Site Configuration
  0- Configure Site Information

  1- Modify WPU IP Address
  2- TrackIQ Deployed Code

 Attached Hardware
  3- Set APC Equipment IP Address
  4- EMS-C10X Environmental Monitoring System model C10X Software

 Site Optional
  5- Time Sync Software [K9 Tardis]
  6- SAIC AVI Tag Reader Consist Downloader

 Menu Support Options
  H- Help
  Q- Quit

Configure Site Information - Details Below
WPU IP Address - Details Below
TrackIQ Deployed Code - Details Below
APC Equipment IP Address - Details Below
EMS-C10X - Install Start Menu short-cuts
Time Sync Software - Installs Tardis (Server) or K9 (Client) Time Sync Software
SAIC AVI Tag Reader Consist Downloader - Install Start Menu short-cuts
Help - Display this Help Document
Quit - Exit without changes

---

This is the Configure Site Information Option;

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

    
The Current [Type] Settings For This Location Are;

  The Company Name Is                         : TrackIQ
  This Site is Located at                     : Pre-Site
  In the Time Zone                            : Australia/Perth

  IP Address For the WPU Needs to be changed  : 10.0.220.10
  IP Address For The PDU is                   : 10.0.220.11
  IP Address For The UPS is                   : 10.0.220.12

Would you like to modify the site settings (Y/N)?

No - Exit without changes
Yes - Enter Parameters as requested
         If an empty response is detected, the previous valid input will be used.
         You'll be prompted if you wish to modify the system after all your responses.

---

This is the Modify WPU IP Address Option;

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

 Please Select the Network Interface you wish to modify;

  0- Loopback Pseudo-Interface 1
    IP Address: 127.0.0.1 & connected
 -----------------------------------------------------------------------------
  1- Local Area Connection
 -----------------------------------------------------------------------------
  R- Refresh

 Rename "Local Area Connection" to one of the following?
  0- "Local Area Connection" - Remain the same
  1- "SITE LAN" - For Site and network connections
  2- "DAQ LAN" - For Data aqusition connections
  S- Switch Interface

Refresh - will update the selection options
         Once an Interface is selected, you'll be prompted to rename it if it is not a already a specific name.

         In a multiple network card systems it's important to identify the network cards correctly.
            Remove all network cables if any are already connected.
            Insert a network cable only in to the First network card (Closest to the WPU power supply) for the SITE LAN.
            Select the "connected" Local Area Connection to rename to "SITE LAN".

Switch Interface - will go back to the start.
         Remain the same - will exit at this point (No changes to be made)
         "SITE LAN" - will prompt if you also want internet access while connected to the TrackIQ office network.
                          If so, it will select the next avaliable IP address in a fixed range.
         "DAQ LAN" - will prompt with a selection of 172.16.X.? addresses to be used.

---

This is the TrackIQ Deployed Code Option;

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

 Now Installing TrackIQ Deployed Software

 Please Select Software to Install.

  0- RailBAMdeploy5.6.3c_New2Msc_20121031.zip
  1- RailBAMdeploy5.6.3c_NoDap_20121031.zip
  2- RailBAMdeploy5.6.3c_New2MscMaster_20130725.zip
  3- RailBAMdeploy5.6.3c_New4Msc_20121031.zip

  R- Return

Return - Exit without changes
Options 0 to Z are Dynamically Generated list of files found on the system
         Files listed above are an example only
         Files located in C:\TrackIQ\Tools\Configure\[TYPE]\MCR???\*deploy*.*
Similarly after deploying the software there is a listing of the Factory Acceptance Test (FAT) Trains
         Files located in C:\TrackIQ\Tools\Configure\[TYPE]\MCR???\*ForTest*.*

---

This is the Set APC Equipment IP Address Option;

TRACKIQ INSTALLATION DISC

_

□

x

2013-08-30

WELCOME TO TRACKIQ INSTALLATION DISC

Ver. 5.2

 Assign IP Address to APC Network Equipment

 May not work If;
   APC Equipment was assigned an IP address previously
   Was connected to a network with a DHCP server

  WPU IP Address needs to Match defined IP Address for this step to work.

  IP Address For the WPU Needs to be changed  : 10.0.220.10

Equipment Type; (A) PDU, (B) UPS OR (R) Return:

Return - Exit without changes
The MAC address of the PDU or UPS is required to Complete this first time only step.

---

Date: 15 May 2025